自動感應門通電前后應做的工作您知道包含哪些嗎？只有正確的認知到感應門的的使用，才能使用正確的進行操作，下面小編來講講濟南感應門通電前后應做的工作！

Do you know what should be done before and after the automatic induction door is powered on? Only when the use of the sensing door is correctly recognized, can the correct operation be carried out. The following section will talk about the work that should be done before and after the automatic sensing door is powered on!

1.自動感應門通電前應做的準備工作：

1. Preparations before the automatic induction door is powered on:

A.在確保自動感應門門體周圍沒有可能會影響自動感應門正常運行并無閑散人員逗留的情況下，可以對自動感應門做通電處理，以免出現傷人事故。

A. Under the condition that there is no idle person who may affect the normal operation of the automatic sensing door around the automatic sensing door, the automatic sensing door can be powered on to avoid personal injury.

B.自動感應門的電源開關位置在自動感應門門體右側安裝于軌道上，仰視即可看到。（一般來說自動感應門應該有一個單獨的開關來控制，這樣將會更加方便）

B. The power switch of the automatic sensing door is installed on the rail at the right side of the automatic sensing door body, and can be seen from the bottom. (Generally speaking, the automatic induction door should be controlled by a separate switch, which will be more convenient)

C.檢查檢測自動感應門自動感應門門體有無破損情況，活動門扉是否牢固固定在軌道上且無卡滯現象。

C. Check and detect whether the automatic sensing door body of the automatic sensing door is damaged, and whether the movable door leaf is firmly fixed on the track without jamming.

2.自動感應門通電過程：

2. Power on process of automatic sensing door:

A.在確保已做好‘通電前的準備'后，即可進行通電

A. After making sure that the "preparation before power on" is completed, power on can be carried out

B.將電源開關合上后（活動門扉好處于全打開狀態），工作人員請不要在感應器的感應區域內活動或逗留，因為這樣門將無法關閉?；顒娱T扉會以一個較慢的速度徐徐關閉（此速度遠比正常速度要慢），此時電腦控制盤正在自動檢測門扉的運行距離及運行情況。

B. After the power switch is closed (the movable door leaf is better than the fully open state), the staff should not move or stay in the sensing area of the sensor, because the door will not be closed. The movable door leaf will slowly close at a slower speed (which is much slower than the normal speed). At this time, the computer control panel is automatically detecting the running distance and running condition of the door leaf.

C.當自動感應門完全關閉后就已進入使用狀態，可放心進出。

C. When the automatic sensing door is completely closed, it is in use, and you can enter and exit safely.

3.自動感應門正常工作中應注意：

3. During normal operation of automatic sensing door, attention shall be paid to:

A.在正常使用中，我們應該切記不要試圖奔跑通行自動感應門，或者在自動感應門中間停留，哪怕是短暫的停留。因為這樣有可能會對您或者自動感應門帶來損傷。

A. In normal use, we should remember not to try to run through the automatic sensing door, or stay in the middle of the automatic sensing door, even for a short time. Because it may damage you or the automatic sensing door.

B.當自動感應門處于非門禁系統工作狀態時，自動感應門將采用微波感應器來接受人體移動信號，當您走離自動感應門約500MM-1800MM左右時（該距離可進行調整），自動感應門將開始打開您可以緩步通行。

B. When the automatic induction door is not in the working state of the access control system, the automatic induction door will use the microwave sensor to receive the human body movement signal. When you walk about 500MM-1800MM away from the automatic induction door (the distance can be adjusted), the automatic induction door will start to open and you can walk slowly.

C.當自動感應門處于門禁系統工作狀態時，您要用門禁系統卡來進入自動感應門。門禁系統卡在距離門禁系統主機（安裝于室外自動感應門右側）約50MM-80MM時主機將會接收到信號并發出“滴”音，然后自動感應門將開始打開，您可以緩步通行。如果您要由室內出來您可以按出門按鈕（安裝于室內自動感應門右側）

C. When the automatic sensing door is in the working state of the access control system, you need to use the access control system card to enter the automatic sensing door. When the access control system is stuck about 50MM-80MM from the host of the access control system (installed on the right side of the outdoor automatic sensing door), the host will receive the signal and make a "drop" sound, and then the automatic sensing door will start to open, so you can walk slowly. If you want to come out of the room, you can press the exit button (installed on the right side of the indoor automatic sensing door)

有可能在使用中，您發現自動感應門停住不再自動。您可以關閉電源，約五分鐘后再通上電源，即可恢復正常。因為該自動感應門具備防夾保護功能和自我保護功能，有可能是在正常工作中夾住異物或者是有人強行拉開過自動感應。更多相關內容就來我們網站http://m.9pop.cn咨詢看看吧！

It is possible that in use, you find that the automatic sensing door stops automatically. You can turn off the power and turn on the power in about five minutes to restore normal operation. Because the automatic sensing door has anti pinch protection function and self-protection function, it may be that the foreign object is clamped in normal operation or someone forcibly pulls the automatic sensing door. More relevant content will come to our website http://m.9pop.cn Consult!